Why More Conway Homeowners Are Switching to Heat Pumps
Picture a mild December morning in Conway. The air outside sits in the low 50s, but inside your home you still want steady warmth without the noise and cost of an old furnace fighting the chill. A heat pump handles this exact situation with quiet efficiency. It pulls warmth from the outdoor air and moves it inside, then reverses the process when summer heat arrives. For a climate like ours, where hard freezes are rare and long, humid summers are the real challenge, a heat pump is one of the most practical comfort systems you can install.
At Conway Air Conditioning, we install heat pumps that carry a home through every season on a single piece of equipment. Instead of buying and maintaining a separate furnace and air conditioner, you get heating and cooling from one integrated system. That simplicity appeals to homeowners across Conway, Myrtle Beach, Red Hill, Bucksport, Aynor, Forestbrook, Socastee, Carolina Forest, Loris, and Garden City, SC, and it is a big reason heat pump requests have grown steadily in our service area. We help you choose a unit that fits your square footage, your insulation, and your budget, then install it so it performs the way the manufacturer intended.
How a Heat Pump Actually Works
A heat pump does not create heat the way a gas furnace or electric strip does. Instead, it moves heat from one place to another using refrigerant, a compressor, and two coils. In cooling mode, it absorbs heat from inside your home and releases it outdoors, which is exactly what a standard air conditioner does. In heating mode, a reversing valve flips the cycle. The system captures warmth from the outdoor air, even when the temperature feels cold to you, and delivers it inside. Because it transfers existing heat rather than burning fuel, a heat pump often delivers more warmth per dollar of electricity used.
Modern heat pumps use variable-speed compressors that ramp up and down instead of simply switching on and off. This gives you tighter temperature control, quieter operation, and better humidity removal during our sticky summers. The efficiency ratings matter here. We look at the SEER2 number for cooling performance and the HSPF2 number for heating performance. Higher numbers mean lower operating costs. When we size a system for your home, we balance these ratings against your comfort goals so you do not overpay for capacity you will never use.
Our Heat Pump Installation Process
A good installation starts long before any equipment arrives. We begin with a load calculation, sometimes called a Manual J, to determine how much heating and cooling your home actually needs. Guessing at capacity is one of the most common mistakes in this trade. An oversized heat pump short-cycles, wastes energy, and leaves rooms clammy. An undersized unit runs constantly and never keeps up. Our measured approach avoids both problems.
Once we agree on the right equipment, our team handles every step from removal to startup. Here is how a typical installation moves forward:
- Site assessment and load calculation: We measure your home, inspect existing ductwork, and confirm the electrical service can support the new unit.
- Old equipment removal: We disconnect and safely remove the old system, recovering refrigerant according to EPA rules.
- Outdoor and indoor unit placement: We set the condenser on a level pad and install the air handler or coil where it drains and breathes properly.
- Refrigerant lines and electrical: We run and seal line sets, then wire the system to code with proper disconnects and surge protection.
- Startup and verification: We charge the system to the exact refrigerant weight, test airflow, and confirm both heating and cooling modes operate correctly.
Before we leave, we walk you through the thermostat, explain the maintenance schedule, and answer every question. As a Factory Authorized Dealer, we register your equipment so your manufacturer warranty stays fully intact. That registration step is easy to skip, but doing it right protects your investment for years.
Sizing and Technical Specifications That Matter
The tonnage of a heat pump describes its cooling capacity, where one ton equals 12,000 BTUs per hour. Most Conway homes fall between two and five tons, but the correct size depends on far more than square footage alone. Ceiling height, window count, insulation quality, and how much shade your lot gets all shift the math. This is why we never quote a size over the phone. A proper installation depends on real measurements taken at your property.
Airflow is just as important as tonnage. A heat pump wants roughly 350 to 400 cubic feet per minute of air across the coil for every ton of capacity. If your ductwork restricts that airflow, even the best unit will underperform. During installation we check static pressure and correct any duct problems we find. We also pay close attention to refrigerant charge, because a system that is even slightly overcharged or undercharged loses efficiency and can shorten compressor life. These technical details separate an installation that merely works from one that truly performs.
Where Heat Pumps Fit Best in Local Homes
Heat pumps suit a wide range of situations across Horry County. All-electric homes benefit the most, since there is no gas line to feed a furnace and the heat pump handles both seasons on its own. Homeowners replacing an aging air conditioner often upgrade to a heat pump at the same time, gaining efficient heating without adding a second appliance. New additions, converted garages, and homes that never had reliable heating are also strong candidates.
Some homes pair a heat pump with a backup heat source for the rare deep-cold nights we occasionally see. This setup, sometimes called a dual-fuel or hybrid system, lets the heat pump do the everyday work while the backup fills in only when temperatures drop unusually low. We help you decide whether backup heat makes sense for your specific home. Because we serve Conway, Myrtle Beach, Red Hill, Bucksport, Aynor, Forestbrook, Socastee, Carolina Forest, Loris, and Garden City, SC, we understand how coastal humidity and mild winters shape the right choice, and we tailor each recommendation to the property in front of us rather than a one-size-fits-all formula.
Why Choose Conway Air Conditioning
Experience matters when you are installing equipment meant to last fifteen years or more. Conway Air Conditioning is one of the oldest heating and air conditioning businesses in Conway, serving Horry County since the 1950s. That long history means we have installed heat pumps through decades of changing technology, and we bring that accumulated knowledge to every job. We are family owned and operated, so the people who answer your call and the people who complete your installation share the same commitment to doing the work right.
Our technicians hold credentials that back up their skill in the field. Here is what those certifications mean for you:
- NATE Certified Technicians: Our team has passed rigorous industry testing on real HVAC diagnostics and installation practices.
- BPI Certified: Our Building Performance Institute training means we look at your whole home, not just the equipment, so your system works with your house rather than against it.
- Factory Authorized Dealer: We meet the manufacturer’s strict standards, which protects your warranty and gives you access to genuine parts.
- President’s Award winner: This recognition reflects a consistent record of customer satisfaction and installation quality.
When you invest in a heat pump, you want it installed by people who will still be here to service it years from now. That is the promise behind our work. We handle every project with the care and precision that a long-lasting system deserves, and we stand behind what we install.
Ready to Talk About Your Heat Pump Installation?
If your old system is nearing the end of its life, or you simply want a more efficient way to heat and cool your home, a heat pump deserves serious consideration. We are glad to visit your property, run the numbers, and give you a clear picture of what a new system will cost to own and operate. There is no pressure and no guesswork, only honest guidance based on decades of local experience.
Reach out to Conway Air Conditioning to schedule your heat pump consultation in Conway or the surrounding communities. We will help you understand your options, explain the technical trade-offs in plain language, and deliver an installation built to keep your family comfortable through every season. Trusted HVAC service in our region starts with a conversation, and we are ready when you are.
